Mazda 6 is a passenger class car from the Japanese concern of the same name.

Since the presentation of the Mazda 6 model until the end of 2018, three generations have been released, namely:

• Mazda 6 GG between 2005 and 2007;
• Mazda 6 GH in 2010;
• Restyled version in 2011;
• Third generation in early 2012.

The changes affected not only the exterior, but also the interior, technical characteristics, power unit, transmission.

Sizes of regular disks for Mazda 6 generations

Alternative rims Mazda 6

• Cast: light weight, low pressure on thrust bearings, hub, transmission;
• Stamped: durable, expensive;
• Forged: durable, one third lighter than analogues.

*check prices in stores at the time of purchase.

• Check the wheel balance on a special diagnostic stand in the workshop. If deviations are found, restore the geometry of the structure. It is impossible to “reanimate” the disk on your own due to the lack of the necessary equipment;
• If you find cracks, dents on the rim, contact the service station for prevention, rolling;
• At high, medium speeds, avoid getting into pits, potholes. The disk is deformed, the tightness is broken, the tire cord is damaged;
• Keep an eye on the pressure in the tires, it should not differ from that recommended by the manufacturer. In case of deviation, pump up yourself, contact the service station;
• Observe the transition to summer, winter regimes. In summer, tire pressure is higher by 0.15 atm., in winter it is lower by the same amount. The parameters are indicated in the vehicle operating instructions;
• Tighten the nuts on the rim with a torque wrench. Excessive tightening contributes to the breakage of the studs, weak - unscrewing. Which will lead to a collision on the road with an oncoming traffic participant.

In sunny weather, cast aluminum wheels are less susceptible to damaging external influences. But in slush, ice, when the road is strewn with chemicals, the rim is susceptible to corrosion. This provokes paint peeling, destruction of the molecular composition, and a decrease in structural strength.

Wash the wheels as they get dirty. Since it is unlikely that it will be possible to wash it with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, service centers.

Systematic polishing allows you to get rid of scratches. Pre-clean the wheel of dirt, dry thoroughly, and then treat with a chemical. Wipe with a cloth several times.

Store wheels upright, do not stack on top of each other. Clean off dirt, dry, wrap with cellophane. Some motorists practice to apply an aerosol to the surface before conservation.

The average service life of original discs is 180 - 200 thousand km. Under the condition of a moderate driving style, the replacement interval will increase by a third. The resource of using tires is 70 - 80 thousand km.

What affects the installation of free-size discs on a Mazda 6 car

The size of tires, disks affect the technical characteristics of the machine. Refer to the instruction manual for recommended and allowable sizes.

For a driver who uses the car as a means of transportation, the "factory" (stock) rim sizes are more than enough. In the case of tuning, changes in standard characteristics, dynamic performance, “change shoes” for the car in non-standard wheel sizes.

The list of characteristics that are changed by installing non-standard wheel sizes on a Mazda 6 car:

• Controllability;
• Road grip;
• Sharpness, responsiveness of the steering wheel;
• Aquaplaning;
• Comfort;
• Noise level;
• Fuel consumption in the combined cycle;
• Protector wear.

Deciphering the marking of disks, tires on Mazda 6

For example, R19 5×114.3 6.5J ET50 (see photo):

• PCD (Pitch Circle Diameter) diameter of the circumference of the center of the mounting holes: 71 mm;
• Disk Radius: 19;
• Number of holes 5;
• Fastener type: M11.0 - stud diameter;
• Thread size (pitch): 1.25;
• Center hole diameter: 67mm;
• Pressure (front / rear): 2.0 / 2.0 bar.

PCD parameter: distance between centers of opposite holes. Measurement of the value with a ruler without dismantling the wheel. For a five-bolt design, the resulting distance must be multiplied by a factor of 1.05.

Rim offset ("ET"): the distance between the disc-to-hub point of contact and the midpoint of the rim width. Designation: DEPORT, OFFSET. The offset is positive if the plane does not go beyond the point of contact, otherwise the offset is negative. The farther the rim is from the body, the more the overhang tends to zero.

• D is the diameter of the central hole, measured in millimeters.
• J, H and subsequent characters in alphabetical order indicate the markings of the humps on the rim shelf. Symmetrical, asymmetrical and combined.
• "Hump" is a protrusion on the rim for a tubeless tire. When driving, the "rails" hold the tire beads, preventing depressurization.

Numeric characters indicate the date of issue, month, year.

• TUV is the abbreviation of the regulatory body for compliance with quality standards.

Maximum wheel load: the unit of measurement depends on the country of the manufacturer of the rubber, rim.

Razboltovka rims"Mazda 6" is a widely used parameter that refers to the way the wheel is attached to the chassis structure of the car. This prevalence is due to the fact that most Japanese and Korean automakers define identical sizes and parameters of wheels and tires to make it easier for motorists to choose. The bolt pattern of the Mazda 6 disks is provided by the factory in one version and is equal to 5 × 114.3, regardless of the generation. As for the wheels themselves, depending on the year of manufacture, they were installed in sizes from R15 to R19. By choosing the right set of wheels and installing them on your car, you can improve the exterior design and get a high level of handling and stability.

If it is necessary to make certain improvements in the appearance or technical characteristics of the Mazda 6 car model, it is necessary to select only spare parts and components from official manufacturers. Every car enthusiast knows that wheels are the main part of the exterior. Much of the design depends on their size, color and shape. Not only the exterior of the car depends on the method of their manufacture, but also the driving performance, which is much more important than the appearance. A vehicle with large rims looks more attractive than a similar vehicle with small rims.

Mazda 6 bolt pattern, configurator

Improving the appearance of the car is certainly important, but it is not the top priority. For any mode of transport, it is more important that changes to the original design do not reduce efficiency and resource. It is recommended to select only such spare parts and elements that would correspond to the factory technical specifications and safety requirements.

In addition to a nice appearance, the installed wheels must fit all the wheel bolt parameters of the Mazda 6 2006, or any other year of manufacture. In addition, there must be full compliance with the established factory dimensions of the products. Inconsistency of the required parameters leads to incorrect and unsafe operation of the car. An incorrectly selected Mazda 6 bolt pattern leads to the fact that the purchased discs simply do not fit, and they will have to be returned back. This gives the car owner unnecessary trouble. There are ways, for example, the use of adapter rings - this allows you to install even unsuitable wheels. However, in this case, the movement will be a constant risk to the safety of the driver and passengers.

With a change in the size and parameters of rims, it is necessary not to forget about the correct selection of a new set of tires.

Razboltovka (PCD) stands for Pitch Circle Diameter. The value implies the number of bolts that are used to fasten the product to the chassis and the diameter of the circle on which the bolts are located in relation to each other. When choosing a new set of wheels, you must carefully consider this parameter. Otherwise, with ignorance, there is a big risk of buying unsuitable products. It does not matter who the manufacturer of the new discs is, they can be original models or products from any other manufacturer. All of them must comply with the allowable parameters and sizes.

This parameter can be measured independently. A simple ruler will suffice for this, but for maximum accuracy it is better to use a caliper. There are no problems with the number of bolts, they are very easy to count visually. But with the size of the diameter there are difficulties. It requires high measurement accuracy and knowledge of special formulas for determining the parameter. It is best to look at it in the official technological documentation for the vehicle or pick it up according to the tables presented on the Internet.

Incorrectly selected and installed wheels for any car are a high risk of a threat to the safety of the driver and passengers.

In the best case, low-quality products will increase the wear of parts and suspension assemblies, and in the worst case, they can cause an accident.

Options for other models

The popular model from the manufacturer "Mazda" CX 5 is a medium-sized crossover and has an increased weight compared to the sixth model. The importance of disks for her is even greater than for a sedan. Therefore, it is very important to use only high-quality and official products for improvement and tuning.

Note!

Only two sizes of wheels are installed on the Mazda CX-5 - R17 and R19.

In addition to the dimensions in diameter and width of the rim, there are no cardinal differences in the parameters from the Mazda 6. It is necessary to consider what are the parameters of the Mazda CX 5 bolt pattern:

• 17-inch with parameters - 5 × 114.3; 7×17; ET50; d67.1. Tires 225/65/R17;
• 18-inch with parameters - 5 × 114.3; 7×18; ET50; d67.1. Tires 225/60/R18;
• 19-inch, having parameters - 5 × 114.3; 7×19; ET50; d67.1. Tires 225/55/R19.

The car "Mazda CX-7" is equipped with the following wheels:

• Rim diameter - 18 inches;
• Width - 7.5 inches;
• Fasteners - 5 bolts x 114.3 millimeters;
• Departure - 50 millimeters;
• The diameter of the central hole is 67.1 millimeters.

On a note.

In this case, the so-called wheel markings are indicated. On the original, it should be embossed on the inside.

It specifies:

• 5 × 114.3 - the number of mounting holes and the diameter of the circumference of their location, or bolt pattern;
• 7 × 17 - the width of the disc and its diameter, measured in inches;
• ET50 - disc offset, measured in millimeters;
• d67.1 - hub diameter, also indicated in millimeters.

Wheel offset is the distance between the planes of application to the hub and the central axis. This parameter is the most important for calculating the characteristics of the steering and chassis.

Departure parameters are specified by the vehicle manufacturer and must be strictly observed. Deviation in one direction or another entails a change in the loads on the chassis. This can lead to a change in steering sensitivity and possible accidents.

The hub diameter indicates the size of the center bore of the disc. It is measured in millimeters. If the selected set of wheels has a larger diameter, then it is necessary to purchase special adapter rings. Often they come as a set.

Note!

Any deviation from the specified factory dimensions may affect steering performance and suspension wear.

Options for "Six"

As for the Mazda 6, which was released in 2008, when selecting disks for a car, the following are taken into account:

• Rim diameter, measured in inches.
• Rim width, also in inches.
• Departure, measured in millimeters. This is the distance from the vertical axis of symmetry to the plane of contact between the hub and the disk.
• The number of holes for fastening with nuts and bolts, or just a bolt pattern.
• The hole for the hub and its dimensions. Marked as DIA and represents the diameter of the central hole. Measured in millimeters.

Taking into account all dimensions and parameters, we can distinguish the wheel markings:

• The bolt pattern, standard for Japanese manufacturers, is 5 × 114.3.
• Wheel width - 6.0, 7.0 and 7.5 J, depending on the radius, measured in inches.
• Disc offset - ET from 50 to 60, depends on the width, measured in millimeters.
• The diameter of the central hole for the hub is d 67.1 millimeters.

Mazda engineers for the most part model range the bolt pattern parameter was chosen equal to 5 × 114.3.

This makes it easy to choose from a wide range of rims on the market. It is possible to choose both original products and products of various brands. The choice of sizes in width and diameter depends only on the personal preferences of the car owner. These dimensions are floating and subject to change. It is not recommended to change the data of the bolt pattern and the diameter of the central hole.

Using the automatic selection of tires and wheels for the car Mazda 6, you can avoid many problems related to their compatibility and compliance with the recommendations of car manufacturers. After all, they have a huge impact on a significant part of the operational properties. vehicle, first of all, on controllability, fuel economy and dynamic qualities. In addition, one cannot fail to note the importance of tires and rims as elements active safety. That is why their choice should be approached as responsibly as possible, that is, with knowledge of a number of parameters of these components.

Unfortunately, only a small part of car owners owns such technical nuances. However, automatic system selection will be extremely useful, regardless, as it will minimize the likelihood of choosing the wrong rims or tires. And there is plenty to choose from, thanks to the widest range of such products presented in the Mosavtoshina online store.

When choosing a wheel for a Mazda car, special attention should be paid to the parameters of wheels and tires. For each model passenger car Japanese manufacturers use their individual sizes. For example, the factory equipment of the Mazda 6 involves the use of 195/65 / R15 rubber. As an alternative, tires 205/50/R17, 205/60/R15, 225/40/R18, 225/35/R19 can be used.

Wheel size for Mazda 6 I GG

• increased load on the wheel bearings;
• loss of aerodynamic performance;
• decrease in vehicle stability.

In addition, such indicators as fuel consumption, handling and safety at the time of driving depend on the choice of wheel sizes.

Before choosing a wheel for a Japanese car, you need to study its parameters:

1. tire width;
2. profile height;
3. speed and load indexes;
4. tire pressure;
5. diameter;
6. departure;
7. number of fasteners;
8. fastener types;
9. circle parameters;
10. center hole.

When choosing non-standard wheel sizes, you can use tire calculator. This device is able to select the optimal sizes of wheels and tires, the wheel load index, taking into account the speed of the car and the amount of ground clearance.

Wheel size for Mazda 6 version GG 2002-2008:

1. thread diameter: 5.

Tire size for Mazda 6 GG

Here is a table where we indicate the wheel load indices, speeds, sizes and pressures in tires on the GG version.

Rims for Mazda 6 GG

Wheel size for Mazda 6 II GH

• 205 denotes the width of a car tire. This indicator is measured in millimeters and is determined by calculating the distance of the side edges of the inflated tire. This does not take into account protective belts;
• 60 shows the profile height of the tire, measured in percentage to the width of the car tire. Thus, to determine the height, it is necessary to know the ratio of 205 mm to 60%. As a result, we calculate the profile height: (60% / 100%)X 205= 123 mm;
• R indicates the radiality of the tire. Translated from English, Radial is the radiality of a car tire. Thus, manufacturers combine rubber and cord when creating a tire. The letter D was also used to designate radiality. However, tires with this designation are practically no longer produced;
• 16 indicates the diameter of the centering hole of the disc, for which a car tire can be used. This indicator is indicated in inches.

Mazda 6 GH 2007-2012 release:

• centering hole diameter DIA: 67.1 mm;
• hub fastener: nut;
• thread: M12x5.

Additional information indicated on the side of the tire:

M&S (Mud and Snow) translated from English mud and snow: off-season and winter tires;

XL (Extra Load) reinforced tire with a wheel load index that is 3 units higher than conventional tires with similar sizes;

AW or AS off-season tires;

Symbol * indicates that the tire is intended for operation in the winter period of time. If this marking is not indicated on the side of the tire, then the rubber is used only for the summer period;

inside, outside– the inner and outer side of the asymmetric tyre. Accordingly, when installing the wheel, the Inside inscription should be located on the outside of the rubber, and the Outside pointer on the inside of the tire;

Water, Rain, Aquatred, Aqua or a symbol in the form of an umbrella indicates rain tires;

Inscription Tubeless- tubeless tire. If there is no inscription, this means that the tire is used with a camera. Tube Type indicator - the tire is installed only with the camera;

Arrow or inscription rotation shows the direction of the tread pattern. Indicated on the side of the tire.

Wheel size for Mazda 6 III GJ

For the Mazda 6 III GJ, a standard wheel size marking is used, as for other Japanese car models.

Before choosing a wheel product, it is necessary to study the standard parameters of the factory-equipped auto disk 7.5 × 17 5 × 114.3 ET50 for the GJ version, where:

• 7.5 shows its width in inches;
• the symbol J indicates the design, the shape of the rims;
• the number 17 indicates the diameter of the disc fit. This indicator should correspond to similar tire parameters;
• 5×3 - PCD disc bolt pattern. The number 5 indicates the number of holes for fastening nuts, 114.3 indicates the diameter of the PCD circle;
• The ET50 marking indicates a disc overhang of 50 mm. Departure is the distance from the mating plane of the auto disk to the middle of the wheel rim. The zone of pressing the rim to the automobile hub is called the mating plane.

Information is attached to the marking of rims on the Mazda GJ 2012-2015:

The inscription Max Load indicates the maximum permissible load on the wheel;

ISO, TUV, SAE - classification standards for determining the quality of a disc, similar to GOST. For each product, one or another quality standard is indicated;

Centering hole diameter DIA: 67.1 mm. This indicator should correspond to the diameter of the hub fit. On casting, manufacturers use a large centering hole. So that the disks can be universal for any type of car.

However, in this situation, the hub fit diameter and DIA are different from each other. Therefore, it is recommended to use a centered adapter ring as a connecting element.

The correct choice of wheel size also depends on the ability to determine the markings of the disk and tire. If the owner of the car does not know the marking designation, then the selected tires or wheels may not fit in size.

Wheel sizes for Mazda 6 III GL

The Mazda 6 GL version has been produced since 2015. Wheel parameters:

hub fastener: nut;

thread M12x1.5;

Tires for Mazda III GL

Wheels for Mazda III GL

Pay attention to the fact that drilling or bolt pattern indicates the fit of the diameter of the rim. In the instruction manual for a car, Japanese manufacturers indicate PCD, the landing diameter.

On Mazda cars, 3 different versions and editions use the same wheel bolt pattern: 5 × 114.3. Thus, this drilling determines that the disc is attached with 5 bolts, and its diameter is 114.3 mm.

Wheel size on Mazda 3

The wheel parameters for Mazda 3 I and II releases are almost identical. The differences are that the second version of the car has higher arches.

Thus, wheels with an offset of 35 and a width of 8 can be mounted on the Mazda 3 II BL. The standard parameters are 16.17-inch wheels with a diameter of 6.5 mm.

Wheels for Mazda 3 2013, III generation BM

Factory wheel sizes for Mazda 3 hatchback and sedan 2013-2017 model year are 16, 18 inches, depending on the configuration. Tires with standard sizes are installed: 215/45/R18, 205/60/R16.

Tire pressure on Mazda 3

When using R16 tires with a load of up to 3 passengers, the pressure of the front and rear wheels must be 2.5 bar. With a load of up to 5 passengers, the pressure of the rear wheels is 3.2 bar, and the front tires are 2.8 bar.

R18 tires with a load of up to 3 passengers should have a pressure of 2.4 bar for the front wheels and 2.3 for the rear tires. Full load up to 5 passengers - rear wheel pressure 3 bar and front tires 2.8 bar. Such information is indicated in the instruction manual for the Mazda 3 III generation.

How to determine the drilling yourself?

Method for determining wheel bolt pattern:

1. the number of fasteners (bolts) is calculated according to the holes located on the disk. For example, Mazda 3 has 5 holes in the disk;
2. the calculation includes determining the distance between the inner walls of the holes and adding to the resulting value of their diameter.

For example, by determining the number of bolts and the diameter of the holes, the owner of the car gets the value 5 × 114.3 for the Mazda 3.

An exception may be 18-inch wheels for Mazda 3 with a front drive axle and an engine size of 2.0, as well as versions with all-wheel drive and a power of 2.5 liters.

Wheel size for Mazda CX5

Starting from 2012, all Mazda CX5 trim levels use 17 and 19-inch alloy and steel wheels marked 17x7J ET50, 19x7J ET50:

• ET - disk overhang 50 mm;
• 7J - rim width;
• centering hole diameter - 67.1 mm and 5 holes for fastening bolts around the disc circumference 114.3 mm; PCD 5×3.

Mazda CX5 can be equipped with wheels with non-standard parameters (-+0.5) inches.

Tires for Mazda CX5

If you use factory wheels for 17, 19 inches, then tires with standard sizes are selected for the CX5 model: 225/55/R19/ 99 V, 225/65/R17/ 102 V. Marking designation:

• 225 - tire width;
• 55.65 - profile height of the tire;
• 99.102 - load index from 750 to 850 kg;
• V – wheel speed index up to 240 km/h;
• R - radial tire design.

If you choose tires according to the load capacity index, then you must take into account the fact that the estimated weight per person is 75 kg. In extreme cases, you can calculate the number of passengers and install tires with a high load capacity.

Disk

Mazda 6 II GH

205 – tire width. The indicator is calculated as the distance between the outer boundaries of the side surfaces of an inflated tire, excluding protective belts. Measured in millimeters.

60 – tire profile height measured as a percentage of the width. What does it mean? To find the height, you need to calculate 60% of 205 mm. Thus, the tire height is obtained: 205 X 0.6 (60%) = 123.0 mm

R - stands for radial tire. From the English word Radial, which means a radial type of tire. It is a method of assembling rubber and metal cord during production. Of course, you can also meet the letter D - diagonal, but such tires have now practically disappeared from production.

16 — the diameter of the hole in the rubber, or on which disk this rubber can be mounted, that is disk diameter. This size is always indicated in inches!

The diameter of the disk cannot be more or less than the diameter of the wheel, you simply cannot put it on. That is, if the rubber is 16 inches (406.4 mm), then the disk should be 16 inches (406.4 mm)!

Additional Information

Mazda 6 GH, production years: 2007 - 2012.

• Fasteners to the hub: nut;
• Thread: M12 x 1.5.

Additional information indicated in the marking on the sidewall of the tire:

• XL or Extra Load is a reinforced tire, the load index of which is 3 units higher than that of conventional tires of the same size.
• M+S or M&S (Mud + Snow) - mud plus snow - winter and all season tires.
• All Season, AW (Any Weather) or AS - all-season tires
• The pictogram * (snowflake) means that the tire is intended for use in winter conditions. If this marking is not on the sidewall of the tire, then this tire is intended for use only in summer conditions.
• Aquatred, Aquacontact, Rain, Water, Aqua or pictogram (umbrella) - special rain tires.
• Outside and Inside are asymmetric tires, during installation it is important not to confuse which side is the outside and which is the inside. When installing, the Outside inscription must be on the outside of the car, and Inside on the inside.
• Rotation or arrow - this marking on the sidewall of the tire indicates the directional tread pattern of the tire. When installing a tire, you must strictly observe the direction of movement.
• Tubeless - tubeless tire. In the absence of this inscription, the tire can only be used with a camera. Tube Type - indicates that this tire must be used only with a tube.

Tire

Disk

Mazda6 III GJ

Regardless of the method of production of disks - cast, forged, stamped, there is a standard marking for the size of disks.

Let's analyze the main parameters of 6 GJ - 7.5Jx17 5x114.3 ET 50.

7.5 - wheel width in inches. Translated into millimeters, it turns out 190.5 mm.

J - character indicates certain design features- the shape of the rims of the disk and serves only for information.

17 is the diameter of the rim in inches, which exactly matches the diameter of the tire.

5x114.3 - PCD (Pitch Circle Diameter) or drilling in Russian. Here, the number 5 indicates the number of mounting holes for the nuts, and 114.3 is the diameter of the circle (PCD) in millimeters on which they are located.

ET 50 - the overhang of this disc is positive and is 50 mm. The disc spacing (or offset) is the distance between the mating plane of the wheel disc and the middle of the wheel rim. The mating plane is the surface by which the rim is pressed against the hub of the car.

Additional Information

Additionally, marking 6 GJ, 2012-2015 may contain information:

• DIA D 67.1 - diameter of the central hole in mm. In an ideal situation, this size corresponds to the bore diameter of the hub. On many manufactured alloy wheels, for greater versatility and applicability to various brands of vehicles, the diameter of the DIA center hole is made larger. In this case, the hub diameter is smaller than the disc DIA, and then a special centering seat ring (adapter ring) must be used.
• MAX LOAD - designation of the maximum load on the wheel (designated in pounds or kilograms).
• SAE, TUV, ISO - an analogue of our GOST, the controlling body. Indicates the standard to which the marking of this wheel conforms.

Tire

Disk

Mazda Mazda6 III GL

Years of issue: since 2015.

Additional Information

• Center hole diameter (DIA): 67.1 mm;
• Fasteners to the hub: nut;
• Thread: M12 x 1.5.

Tire

Disk

The marking of tires and wheels carries a lot of necessary information, it is important to be able to understand it. Without this information, you will not be able to choose the right tires for your car, they simply will not fit in size. Special plates with recommendations for tire dimensions are applied to the car body, just read them and go to the store for new ones. However, there are not always such plates, and you have to determine the size of the Mazda 6 tires yourself!