– uncork the filling nozzle. Bend back the felt layer at the bottom end so that the cotton balls become visible. Pointing the tip of the container at the cotton filler, saturate it (see Fig. 2)
Buy lighter fuel

After impregnation with fuel, close the felt layer back. Then insert the inside of the lighter into the housing. Do not allow fuel to come into contact with your skin or eyes when refueling. If liquid gets into your eyes or skin, rinse thoroughly with water and consult a doctor! Before using the lighter, be sure to check that no gasoline has come into contact with the lighter, or on your hands or surrounding objects. Otherwise, remove gasoline from surfaces and ventilate for two minutes. It is recommended to store the lighter vertically, with the lid facing up, especially when refilling for the first time.

Remove the insert from the housing. Unscrew the screw at the bottom end that holds the spring (Fig. 3). Then carefully remove the spring from the tube. Get rid of old flint particles. Check the tube carefully for any remaining spent flint. Install the new flint into the tube, then install the spring in place. Tighten the screw so that the lighter closes freely after setting the bet. Do not apply any serious force when screwing in the screw! Buy a flint for a lighter

Replacing the wick

Unscrew the screw at the bottom end that holds the spring (Fig. 3). Then carefully remove the spring from the tube. Get rid of old flint particles.

Remove the layer from the felt. Remove the cotton pad. Install the wick by pulling it from the bottom through the eyelet. Check that the wick does not protrude beyond the wind protection. Place the cotton filler back, while placing the wick between the layers of filler as shown in Figure 4. Buy a wick for a lighter

Install the felt layer. Place the new flint in the tube and install the spring. Tighten the screw so that the lighter closes freely after setting the bet. Do not apply any serious force when screwing in the screw!

Fuel evaporation over time

Original Zippo fuel evaporates even when the lighter is not used, since it is made from natural materials. It is recommended to refill the lighter before each long trip, as well as from time to time as needed.

Use only original Zippo consumables, they are created specifically for Zippo lighters and heaters. Flints made by other manufacturers may damage the ignition wheel due to the harder material used.
Make sure the wick is installed correctly (as described earlier).

Refilling the Zippo Hand Warmer catalytic heater

Remove the cover with the holes, then remove the catalytic cartridge (Fig. 5.1). Turn the heater over and drain the excess gasoline. Pour ZIPPO 3141 or ZIPPO 3165 fuel into a plastic beaker (Fig. 5.2) as follows:

Do not overfill the heater with gasoline, this may lead to malfunction of the heater, fire and burns!

Remove any remaining fuel from the surface of the heater with a napkin. Insert the catalytic cartridge into place until it stops (Fig. 5.4). Close the fuel container tightly and remove any fuel that gets on the surface. Avoid contact of fuel with skin and eyes. In case of contact with eyes or skin, rinse thoroughly with water and consult a doctor!

Having tilted the heater, warm up the catalytic cartridge in the flame of a match or lighter for 5...10 seconds (Fig. 5.5). Insert the cover with holes into the seat until it stops. Insert the Zippo Hand Warmer into the case supplied (Fig. 5.6), and then tighten the loop on the case.

The cover is designed to regulate the supply of oxygen for the oxidation process. Do not operate the heater without a cover under any circumstances, this will lead to malfunction of the heater, fire and burns!

After refilling, your Zippo Hand Warmer will keep you warm and comfortable! The principle of operation of the heater is to radiate heat during the chemical reaction of gasoline vapor and catalyst.

If it is necessary to stop the heater, separate the catalyst. To do this, use the edge of the lid or a knife. The catalytic cartridge is very hot; to avoid burns, remove it with extreme caution.

The catalytic cartridge cools down within one minute. The heater can then be assembled and inserted into the case. The service life of the catalytic cartridge is 70 cycles. One cycle – 24 hours of continuous operation.

Few people know that lighters were born much earlier than safe matches. Leonardo da Vinci experimented with the first inconvenient and cumbersome models, but his invention remained unappreciated by his contemporaries.

Then, at the beginning of the 19th century, the Dobereiner lighter (named after its creator) was designed - a hydrogen fuel device that explodes if handled carelessly. It was only by the mid-19th century that the gasoline lighter was invented. Over time, it has undergone minor design changes, but the principle of operation remains the same.

Today there are lighters in every home. These useful things are needed not only by smokers: they are used on hikes, on summer vacations, and used for various household needs.

Types of lighters

By fuel type, devices can be divided into:

• gasoline;
• gas;
• USB lighters (coil) - like a car cigarette lighter, where electricity is used as a heating source for the coil.

According to the ignition device:

• silicon;
• piezo lighters;
• with an electrical circuit that provides ignition.

Gasoline lighters are made only with a silicon mechanism. Gas engines are produced with different ignition mechanisms; there are also turbocharged models.

In order to better understand all the pros and cons of gasoline lighters, let’s compare them with gas ones.

Pros and cons of gas models

For the purity of the experiment, we will compare silicon devices running on gasoline and a mixture of propane and butane:

Pros and cons of gasoline lighters

1. Price. There are no cheap models on the market. There are relatively inexpensive copies of well-known world brands, usually made in China. Gasoline lighters today are not just a useful thing, but a stylish accessory of a recognizable brand. Therefore the price is appropriate.
2. Reliability. The mechanism is super reliable, as there is simply nothing to break. Fuel container, wick, flint - everything works for years without failure, and in any weather.
3. Durability. They may outlive you. Expensive products can be passed on by inheritance as valuable property.
4. Easy to refill. Despite the fact that the design of gas and gasoline lighters is almost the same, refueling the latter requires more caution.
5. Maintenance cost. Good branded lighter gasoline costs more than a gas can.

It is also worth mentioning that gasoline tends to evaporate, and the lighter may suddenly appear empty after it has not been used for some time.

Which one should you choose - gas or gasoline? If you need a simple, functional, inexpensive thing, then you should buy a gas one. And if you need a stylish status accessory or a trinket to show off, then you should buy a good gasoline lighter from one of the world’s famous brands.

Best in the world

In a world where many things have become disposable, including lighters due to disgusting quality, I want to be a little nostalgic and return to the Soviet past, where everything was made with a threefold safety margin. In the USSR, gasoline lighters were made to look like small pistols with the inscriptions “Baku,” “Tbilisi,” and “Rovno.” There were other models, gift ones - in the form of cameras and tabletop trinkets. But the best were “military”, army lighters. They were also called commanders. Later, products imitating the original Zippo appeared.

They also made gasoline lighters with their own hands - from brass and steel tubes, coins and other scrap metal. There were more craftsmen in those days; almost everyone knew how to make something from scrap materials. Today there are also people who love to do everything with their own hands, including gasoline lighters. But this must be done carefully, with the full understanding that if the elements are soldered incorrectly, the lighter may burst into flames in your hands.

Today, the world's best gasoline lighters are produced under the brands Cartier, Givenchy, BIC, and Dunhill. But the market leader is the Zippo brand.

Brand Zippo

Zippo gasoline lighters were born when the enterprising American George Blaisdell brought home a test batch of Austrian IMCO lighters. But he couldn’t sell a single device, and started improving them. This is how the legendary Zippo was born, working in any weather.

From the drawings on the body of these products one can trace the entire history of America - all achievements in the military, scientific or sports fields were reflected in the engravings on the body.

The Zippo company has always produced, and still produces, only gasoline lighters. 45,000 products are produced daily. Most of them are relatively inexpensive mass-produced items. But there are also exclusive models, with a case made of gold, silver and titanium.

How to refill

How to refill a gasoline lighter? To do this you need to do the following:

1. Buy the “correct” gasoline for lighters, the best is the original Zippo.
2. Ventilate the room - there should be no extreme heat in the room.
3. Remove all flammable items.
4. Check that all fuel in the lighter has been used up.
5. Remove the lighter from the housing.
6. Find the valve and turn it up.
7. Pour in fuel: be careful not to let gasoline spill onto the edges or overfill the container.
8. Close the valve and, if necessary, wipe the lighter from gasoline with a damp cloth.
9. Collect.
10. Before use, check for leaks to avoid fire.

Remove the inner part (insert) from the lighter body (Fig. 1). Prepare a can of Zippo Premium Lighter Fluid and lift up the filler spout. Lift up the corner of the felt pad on the bottom of the insert to expose the cotton balls. Take a can of fuel and point the filling spout into the cotton balls (Fig. 2), carefully saturate the material so as not to overfill. Be careful when refilling your lighter to avoid getting any liquid in your eyes as this may cause irritation. In case of contact with eyes, rinse thoroughly with water. Place the insert back into the lighter body, before lighting it, make sure that there are no fuel residues on the surface of your hands and the lighter, otherwise wipe with a napkin and let it air for 2 minutes. Close the fuel canister and make sure that there is not a drop of this liquid left nearby - it is highly flammable. If you store your Zippo lighter in your pocket, we recommend that you carry it in an upright position, with the bottom down, especially after the first refill.

How to change flint?

Remove the insert from the lighter body. Turning the insert over reveals the head of the screw that holds the spring that secures the flint. Carefully unscrew the screw, remove the spring and the remainder of the used silicon from the hole (Fig. 3). Make sure there is nothing left there, place the new flint in the hole, then insert the spring and tighten the screw. Make sure the screw is tightened as far as necessary so that you can close the lighter easily.

How to change the wick?

Remove the insert from the lighter body. Turning the insert over reveals the head of the screw that holds the spring that secures the flint. Carefully unscrew the screw, remove the spring and the remaining used silicon from the hole. Remove the felt pad from the insert - using tweezers or tweezers, remove all of its cotton filling (cotton balls) from the inside of the insert. Place the wick into the insert, pulling it from the bottom through the smoke hole using tweezers. Make sure that the length of the wick matches the height of the windproof part of the insert. Place the filling material back into the insert, placing the wick in waves in the intervening layers of cotton (Fig. Basic Ingredients). Reinsert the felt pad. Make sure there is nothing left in the flint hole before placing a new flint, inserting the spring and tightening the screw. Make sure the screw is tightened as far as necessary so that you can close the lighter easily.

Why does the fuel (gasoline) for Zippo lighters evaporate over time?

Due to its natural origin, original Zippo fuel evaporates even when you are not using your lighter. We recommend that you fill your Zippo before a long trip or excursion. Periodically refill your Zippo lighter as needed. Problems that arise when using a Zippo lighter. We hope you are using Genuine Zippo Fuel and Flint as they have been specially designed and created to ensure that your Zippo lighter performs at its best. The material from which silicon is made from another manufacturer can damage the wheel of the Zippo mechanism, and, accordingly, your Zippo lighter. It is also necessary to ensure that the wick in the inside of the lighter insert is positioned neatly and correctly (see instructions above).

Identification codes on the bottom of Zippo lighters!

Over the years, reliable and convenient, Zippo lighters have become widely popular and valuable among collectors. One of the main factors of value is the age of the lighter. But how can it be determined? Very simple. The code located on the bottom of the lighter determines the month and year of production of each specific model. However, the code on the bottom of the lighter is necessary not only for collection purposes, but also so that you can find out the production date of lighters returned for repair. Deciphering the code allows you to find out not only the release date of the lighter, but also its name and series.

Table of decoding identification codes for Zippo lighters.

The date marking system from January 7, 1986 was replaced by an encrypted year/month coding system, with the year marked in Roman numerals on the right side of the bottom of the case, and the month in Roman letters on the left (A= January; B= February, etc. ).

Since 2000, when marking lighters, the Zippo logo is depicted on the left side of the lower part of the lighter body, the letter of the month in the center, and the year of manufacture on the right, instead of Roman numerals.

In 2001, this system was further improved: the designation of the month in the form of Latin letters from A to L remained the same, and the year of manufacture now consists of its last two digits, depicted on the right side of the lower part of the Zippo lighter body.

Makes it possible to significantly extend the time of its use. Periodic replacement of some spare parts, cleaning and refueling are necessary in this case. To replenish the fuel reserves in the accessory, you must follow safety measures, carrying out the procedure away from sources of fire (fireplace, burning candles, fire). It is worth remembering that gasoline vapors flare up very quickly.

The process of refilling a Zippo lighter

Before you start refueling, you need to buy it. Of course, manufacturers recommend using only. To avoid exposing the filling of the accessory to unnecessary risks. Low-quality flammable liquid leads to rapid wear of the wick and poor flame quality. It takes more time to light a lighter filled with regular gasoline. In addition, the unpleasant odor in this case will be very obvious. If it is not possible to purchase original gasoline, then you can take worthy analogues of Zippo fuel, of which there are many on the modern market, but you should not take risks by filling the product with lighter fluid or alcohol.

Step-by-step filling of the lighter with gasoline:

1. First you need to open the lid of the lighter and carefully pull out its “insides”. If the case is being disassembled for the first time, you may have to put in a little effort.

2. The body is put aside for a while. The inside of the product must be turned upside down. On the bottom platform there is felt with the inscription “Lift to fuel”, which translates as “lift to refuel”. Following the instructions, you need to lift the felt. There is cotton wool underneath.

3. The liquid from the canister must be poured onto this cotton wool in a small amount, pressing it in little by little. Manipulations should be continued until all the fibers are completely saturated with gasoline.

4. The protective felt must be replaced. The inner part of the lighter must also be inserted into the body in its original position.

5. It is better to leave the lighter for a few minutes so that the gasoline is well saturated. Hands must be washed thoroughly, getting rid of possible gasoline residues on them.

The accessory is ready for use!

In some cases, after refueling, the lighter does not ignite. Then you should repeat all the previous steps and add more gasoline. It is recommended to clean the lighter simultaneously with refueling, so as not to disassemble it again in the future. If you fill the accessory over the sink, it will be easier to clean up after all the manipulations.

Do not overfill the lighter with gasoline, so that after further use it will not end up on fire. Refilling should be stopped when the cotton wool is completely saturated. If the Zippo does not light, you can turn it upside down to allow the wick to soak thoroughly. Do not pour too much fuel into the lighter in one fell swoop, otherwise it will simply spill and create an unsafe environment. You cannot perform the refueling process on a varnished or wooden surface, because gasoline can damage it. You should pull out the insert very carefully so as not to damage the “filling” in the form of flint and wick.

If you are planning a long-term hike, then it is better to take care of refilling the lighter in advance, “reinforcing” it properly. However, you also need to take a can of gasoline with you on your trip. Special branded fuel containers are designed so that their use in camping conditions is very simple. If you fill it up correctly, the next “feeding” will not be needed soon.

Remove the lighter from the housing. Make sure the lighter is filled with fuel. Insert the inner part into the body of the lighter, wipe the entire surface of the lighter so that there is no fuel left on it. The lighter must be refilled away from sources of fire and flames. Remove the inside of the lighter from the housing. If you store your Zippo lighter in your pocket, we recommend carrying it in an upright position with the bottom facing down, especially after the first refill.

Zippo/ka...ZIppo lighters have a long service life and are extremely unpretentious; they accompany you everywhere: at work, on vacation, on a hike. A Zippo lighter is more than just a fashion accessory. Start by purchasing lighter fluid.

However, only original Zippo fuel will give you an exact guarantee of the durability of the lighter and the absence of an unpleasant odor. After assembly, set the lighter aside for a few minutes until it is sufficiently saturated.

In order to find out whether the lighter has been refilled correctly, you need to check it (preferably indoors). It is necessary to take into account that Zippo refilling has its own characteristics, knowledge of which will help you avoid mistakes that could lead to damage to the lighter.

How to properly refill a Zippo lighter: gasoline

It is very important after refueling the Zippo to thoroughly wipe the lighter with a dry cloth in case you accidentally drop gasoline on the Zippo. The cost of a mistake can be high! For your own safety, do not refill your lighter alone and have fire-resistant items at the ready, such as a clean, damp handkerchief.

Lighters of this class are very delicate and require special treatment. By the way, since you have disassembled your lighter for refilling, you can also clean it of dirt. If your favorite Zippo lighter runs out of gas, don't rush to throw it away.

Windproof lighters

Be sure to inspect the lighter from all sides and the place where the refueling process took place. Avoid contact with eyes. To do this, try not to touch them or wipe them while refilling the lighter. It is recommended to wear closed clothing and gloves during the process of refilling the lighter.

Why does Zippo lighter fuel evaporate so quickly?

Zippo fuel fluid is completely natural, so it tends to evaporate relatively quickly, which continues even when the lighter is not in use. When going on a long trip, it is recommended to refuel the product before leaving, just in case.

A gas cylinder can be used several times, but after each refill the pressure inside it will decrease. Therefore, before proceeding directly to this process, you need to keep the lighter in the freezer for some time, which will make it possible to fill it in a larger volume.

Zippo lighters are famous for their quality and durability. You can take any lighter fluid, just not liquid for charcoal, making fires and barbecues. Pour the liquid from the container onto the cotton wool. If you purchased a large container of lighter fluid, first pour a small amount into a smaller bottle that you can squeeze. To do this, we naturally need a lighter in good condition and a gas can for refilling lighters.

The room in which you are going to refill your lighter should be ventilated and there should be no ignition sources nearby. Do not refill the lighter all the way. Gas enters the lighter under pressure and if it overflows, the lighter may explode. The lighter refill bottle comes with adapters for different valves.

When refueling, it is best to hold the cylinder in your left hand and the lighter in your right, but if you are left-handed, then the opposite is true. In order to fill the lighter more completely, before refueling, place it in the freezer for a few minutes.

Before moving on to the issue of refilling, we need to talk a little about what you can use to refill your lighter. It is best to refuel the lighter with specialized gasoline, although you can use regular gasoline or cuirassier gasoline.

To understand how to refill a gasoline lighter, we will look at refilling a Zippo lighter, since there are many types of gasoline lighters, but the principle of refilling them is the same. Taking the lighter out of the case, we see a felt gasket; bend its corner so that the cotton balls are visible. Now return the felt gasket to its place and reassemble the lighter with the body. Bend its edge, under it you will see the lighter filler.

After that, light your lighter. This is especially important for those who are used to carrying their lighter in their pocket. Evaporation continues even when the Zippo lighter is not in use. The famous lifetime warranty applies to all petrol lighters by default.

How do I change the wick on my windproof Zippo lighter?

We engrave on lighters purchased in our store. Branded fuel Zippo Premium Lighter Fluid is gasoline purified from oily additives. The Zippo lighter works flawlessly on it: it lights up from the first click and produces a steady flame. Disadvantage: high volatility, completely evaporates in a few weeks even from a closed lighter.

A regular zippo holds about 10 ml of fuel. On average, the lighter has to be refilled once a week. You may have to use force. If the insert in a new lighter turns out to be a little worn, this is normal. 5. Pour fuel into the insert. Don’t rush: cotton wool does not immediately absorb liquid. When you see that the balls are completely saturated with fuel and it rises to the edges of the insert, finish refueling.

To avoid this, the manufacturer recommends wearing the lighter upside down for the first time after refueling. For which either a branded case or a narrow jeans pocket is useful. During this time, we advise you to wash your hands and wipe the outside of the lighter, even if they look dry.

Buy lighter fluid. Fuel for lighters of the Ronson brand Zippo design is designed for highly purified gasoline. It's no surprise that your favorite lighter might run out of gas. You can purchase fuel for refilling Zippo Lighter Fluid lighters in the online store Kupivdom.ru.