Lubricants are a necessary element of the safe operation of a car. What oil to pour into the Chery Amulet engine Features of engines and lubrication systems in Chery Amulet

16.07.2021 Lubrication system

Filling the engine oil is a simple and easy task that even a novice driver can handle. To do this, you just need to know how to change it (procedure), as well as be able to determine the spent substance and select a new one corresponding to it.

Features of engines and lubrication systems in Chery Amulet

Chery Amulet's car first appeared on the market back in 2003 with a 1.6-liter engine and a capacity of up to 116 liters. With. Now there are several variations of the model with engines from 1.5 to 1.8 liters. Mostly they are out of production, but are sold both in showrooms and on the secondary market.

In the basic configuration, the models use three types of engines (volume - 1.6 liters):

SQR480ED;
SQR480EC;
TRITEC 1.6L.

These are water-cooled, 4-cylinder in-line engines. The first two have 2 valves per cylinder, and the third - 4.

These motors have a built-in combined lubrication system (both under pressure (for camshaft bearings, main and connecting rod bearings) and by splashing). V this system includes the following components:

oil pump (gear);
oil receiver;
oil sump;
full-flow filter;
pressure meter.

The movement of the lubricant passes through the lubrication channels.

What kind of oil is used in Cheri Amulet?

Chery Amulet, produced since 2006, is filled with the following types of engine oil:

semi-synthetics;
synthetics.

In previously released models, it is possible to use mineral (or rather, hydrocracking) oil.

When choosing products, they are guided by the viscosity index (SAE) and the oil quality index (API). And what newer car, the higher the requirements for motor lubrication. For example, mineral water can be poured into the Chery Amulet 2003 engine, after 2006 - semisynthetics, and in the restyled variation (2-3 generation) - preferably only synthetics.

In addition, it is worth paying attention to which season the oil is designed for: summer, winter or year-round use.

How do you know when to change your oil?

First of all, you need to follow the manufacturer's instructions. So, CHERY in the technical documentation for its brainchild recommends pouring oil at least once a year (or every 10 thousand kilometers).

But if you use a car in difficult conditions (dusty air, engine overload, etc.), it is worth replacing the lubricant at least every 5000 km. This will help protect the engine from premature wear.

A Chery Amulet engine should have 3.5-4 liters of oil for normal operation. It is necessary to monitor the indicators of the oil pressure sensor. If the emergency lamp is flashing, then it is worth checking the fluid level and refilling / replacing it.

The level is checked using a special dipstick according to the following procedure.

Stop the engine, open the hood and wait 3-5 minutes (so that all the oil flows into the crankcase).
Check filter and crankcase for leaks while waiting. If there is a leak from the crankcase, you need to fix it: with a rubber patch, "cold welding" or other materials at hand. If the filter is damaged, it must be replaced urgently. Also, leakage in this place may be due to insufficient tightening.
Remove the dipstick from the crankcase, wipe it, insert it into place and remove it again. Normally, the oil level mark should be between the marks on the dipstick.

It is also worth paying attention to the condition of the oil:

structural changes (graininess, lumps);
unnatural smell (for example, burning);
discoloration (darkening, blackening).

How to change or add engine oil in Chery Amulet?

The oil is topped up through the oil filler neck. It is necessary to use the substance that is already in the engine (not an analogue, not similar, but exactly that). It is necessary to unscrew the plug and pour in oil a little, while checking the level with a dipstick.

With a complete replacement, the motor is pre-washed in order to completely exclude the possibility of mixing different oils. The process of pouring new fluid takes place in stages, immediately after stopping (with a hot engine).

Open the oil filler cap.
Unscrew the drain plug and drain the oil into a container.
Check the condition of the gasket on the drain plug, replace if necessary.
Flush the engine with special flushing oil (or the same one that will be filled in).
Screw up drain plug.
Remove the oil filter with a special wrench.
Lubricate the O-ring of the new filter with oil.
Put the filter back in place and manually lock it by turning it 3/4 of a turn.
Fill in new grease through the oil filler neck (3.5-4 l).
Close the stopper.

After that, the engine is started at Idling... In this case, the emergency lamp on the pressure sensor should go out. After 3-5 minutes, check the level again and, if necessary, add more.

So, you need to replace the lubricant in the engines of Chery Amulet cars after 10 thousand km of the road or a year of driving if you drive under normal conditions. In the presence of harmful factors, the frequency increases - up to times per 5000 km.

Quite simple, it would seem, for every motorist, the question of replacing the oil in the engine, nevertheless, requires more than a specific answer. Of course, all tasks are possible Maintenance machines (including the replacement of oil and filters) are completely entrusted to the masters of the car service, including the choice of engine oil. However, it is much preferable to figure out such an elementary issue yourself - often awareness can save significant money, and also reduce the time for scheduled maintenance of the car.

In particular, the drivers of the popular "Chinese" Cherie Amulet, for which detailed information on the Internet and in print was almost completely absent a few years ago, a small educational program on the choice of motor oil will come in handy. For ten years, this truly "people's" car has undergone restyling twice, but the choice of power units remained small. Chery Amulet is equipped with either a reliably time-tested 1.6-liter eight-valve engine. from FORD marked "SQR480" with a capacity of 94hp, or a more modern and powerful engine "SQR477f" with a volume of 1.5 liters. and 16 valves, which already produces 109hp at 6000rpm. First power unit more unpretentious both to fuel with different octane numbers, and to motor oil of various brands. The second version of the motor is the most demanding.

What can be butter?

Having omitted the difference between oils for diesel and gasoline engines as unnecessary (in the context of Cherie Amulet's maintenance), consider the types of oil - there are three of them.

Mineral engine oil. The key technology for the production of mineral oil is the atmospheric distillation of crude oil.
Semi-synthetic or hydrocracking oil - this type of fuel and lubricants at the first stage is produced using the same technology as mineral oil, but for a more thorough separation of fuel oil it is additionally subjected to vacuum distillation. This allows you to get much higher performance characteristics comparable even to synthetic oils.
Synthetic oils are the most complex and expensive group. These include oils based on polyalphaolefins (PAO), esters (esters), GTL - (synthesis of liquid hydrocarbons from gas). All oils produced on a synthetic base have outstanding protective, cleaning, and anticorrosive properties. However, for this such luxury one has to pay one and a half, two, or even four times more than for a similar oil for hydrocracking.

For reference: any oil containing more than 5% synthetics can be called a semi-synthetic oil. And also in Ukraine it is not obligatory to classify oils according to the content of the base base, therefore "Synthetic" is not always so. And 95% of oils sold on the market are in fact hydrocracked with the addition of a certain% of a synthetic base.

Engine oil classifications

ACEA classification:

A / B: oils for gasoline and diesel engines:

ACEA A1 / B1: energy-saving oils with especially low viscosity, can only be used with the direct approval of the engine manufacturer; the category has been canceled since 2016.
ACEA A3 / B3: oils for gasoline and diesel engines passenger cars and light trucks operating under severe conditions and with extended drain intervals.
ACEA A3 / B4: oils for gasoline and diesel engines of cars and light trucks, operating with extended oil drain intervals, superior in their characteristics to oils corresponding to A3 / B3 categories
ACEA A5 / B5: Low viscosity oils with HTHS viscosity between 2.9 and 3.5 mPa · s may not be suitable for certain engine models.

C: oils with increased compatibility with catalytic converters (low ash oils):

API classifications:

SA - Pure mineral oil without additives;

SB - Not applicable to most engines built after 1951.

SC - Not applicable for most engines built after 1967.

SD - Not applicable for most engines built after 1971.

SE - Not applicable for most engines built after 1979.

SF - Not applicable for most engines built after 1988.

SG - Not applicable for most engines built after 1993.

SH - Not applicable for most engines built after 1996.

SJ - For engines of cars manufactured not later than 2001.

SL - For engines of cars produced no later than 2004.

SM - For engines of cars produced no later than 2010.

SN - Introduced in October 2010.

On Cherie Amulet, what kind of oil to fill in the engine?

Engine oil for Chery Amulet 1.6 8V SQR480

Let's start with our good old 1.6 SQR480 engine, which we inherited from Ford with all its advantages and "sores"

Filling volume - 3.9l

Permissible viscosity - 5W30 (new engine or engine that has been run-in after overhaul) / 5W40 (optimal oil for everyday use) / 10W30 and 10W40 (option for engines with high mileage and non-critical oil level).

Classification according to ACEA A3 / B3 or A3 / B4, according to API SL / SM / SN (SJ as a last resort)

Critical oil consumption - more than 1 liter. for 1 thousand km

Engine oil for Chery Amulet 1.5 16V SQR477f

Filling volume - 3.9l

Allowable viscosity - 5W40 (optimal oil for both a new engine and for everyday use) / 10W40 (option for engines with high mileage and non-critical oil level).

Classification: ACEA A3 / B3 or A3 / B4, API SL / SM / SN

Critical oil consumption - no more than 1 liter. for 1 thousand km

Let's summarize:

For the 1.6 engine, the main focus in the choice of oil is better to highlight its washing characteristics, since in this engine there is a problem with coking of the oil channels of the hydraulic lifters, which ultimately leads to wear of the camshaft cams.

For the 1.5 engine, on the contrary, the emphasis is on the protective properties of lubricants and this is due precisely to the increased power relative to the engine volume. Therefore, we advise you not to buy energy-saving oils for this motor that are classified according to ACEA A1 / B1 or A5 / B5.

We hope that this article will help you make the right choice and prolong the life of your four-wheeled friend's heart.

GasolineAPIDieselAPIA typeRecommended manufacturers 2006 SLCIsemisyntheticsMobil, Xado, Valvoline, Kixx, G-Energy, Rosneft, Mannol 2008 SMCI-4semisyntheticsMobil, Lukoil, Valvoline, Xado, ZIC, Kixx, G-Energy 2010 SMCI-4synthetics, semi-syntheticsCastrol, Mobil, Xado, ZIC, Lukoil, Valvoline, Kixx 2012 SMCI-4synthetics, semi-syntheticsSHELL, Castrol, Mobil, Xado, ZIC, Lukoil, Valvoline, Gt-Oil 2014

To buy a suitable oil, you will need to name - the SAE viscosity index and the acceptable - API quality oil for diesel or gasoline engine... (The choice of the manufacturer is at your discretion). For example: for gasoline engine Chery Amulet (1st generation) 2006 onwards, suitable - all-season semi synthetic oil 10W-40 with SL quality, and for models of 2014 onwards, for the cold season, synthetics 0W-40 \ SN are well suited. If possible, check the selected oil against the vehicle manufacturer's specifications and service intervals. Oil condition - drop by drop Optional

autogener.ru

Lubricants are a necessary element of the safe operation of a car

One of the most common questions motorists ask is what kind of oil to put into the engine. Especially often people who have bought vehicle from a manufacturer they don't know much about.

Cherie Amulet in all its glory

For example, the owners of Cherie Amulet. To do right choice, everyone should try to figure out the characteristics engine oils... This will help you figure out which one is best for your vehicle.

The viscosity of the product is always encoded in the label, which looks like this: SAE 10W-40. The SAE abbreviation means that this oil has been tested by the Society of Automotive Engineers, which regulates the viscosity of automotive lubricants internationally. The W symbol indicates that the product can be used in winter. The peculiarity of such a lubricant is that it allows you to quickly start the engine in severe frost conditions.

The number after the letter W indicates the maximum temperature at which the engine oil will retain its properties. The 10W-40 symbol combination means that this grease can be used in all weather conditions, whatever the season. Winter oil would be labeled SAE 10W.

When choosing oil according to the viscosity parameter, pay attention to the pattern of its labeling depending on the temperature at which it can be used.

At a negative temperature of 30 degrees and below, the lubricant must have a 0W mark.
At temperatures from -20 to -25 degrees - 5W.
-15 to -20 - 10W.
If the air temperature in winter ranges from -10 to -15, then you should choose engine oil with the designation 15W.
-5 to -10 - 20W.
If the average temperature is up to -5, auto chemicals with a 25W icon are used.

Consider these characteristics when choosing a lubricant, and your car will never know what oil starvation is. A similar situation occurs if, during engine start-up, the lubricant does not have time to wash all the parts, forcing the mechanism to run dry, which can lead to its destruction.

Back to the table of contents

The difference between mineral products and synthetic

Each of these types of products differs from each other at the molecular level. Synthetic engine oil, both chemically and thermally, has greater stability of parameters. This means that during engine operation they do not change their properties, which does not have a very favorable effect on the car mechanism.

Synthetic products prevent the formation of deposits on engine parts, and this is their advantage over mineral lubricants. In addition, they have a longer service life. When using lubricant, check for cracks in engine parts. If there are any, then you cannot avoid drips. It is recommended to switch to synthetics after the Cheri Amulet motor has worked on a mineral product, and then on a semi-synthetic one.

When switching to synthetics, you need to check the strength of the seals, the absence of leaks and deposits. If found, the seals should be replaced. Deposits can be removed by flushing the oil system. To detect smudges, fill in semi-synthetics and watch the engine. If they did not appear when using this type of auto chemistry, you can safely switch to synthetics.

Back to the table of contents

Changing the lubricant and filter in the engine

Add grease

The manufacturer Chery Amulet recommends changing the lubricant one year after the start of use or after the car has traveled 10 thousand km. If Chery Amulet is operated in heavy and dusty conditions, you need to change the lubricant after 5 thousand km.

In order to replace the lubricant in the engine of a Chery Amulet car, you will need a new engine oil, a rag, a filter, and a wrench designed to unscrew it. Before starting the replacement procedure, warm up the car engine. Then refill with the same grade of engine oil that was used previously. If you intend to change the brand, then first you need to completely flush the lubrication system of your Chery Amulet.

After that, you can fill in new lubricant, but only up to the minimum mark on the dipstick. Then start the Chery Amulet engine and let it idle for about 10 minutes. Then drain the waste fluid and replace the filter. Only now can you add oil to the upper mark of the dipstick.

It is not necessary to drain the working off on the ground, use some kind of container.

The process of changing the oil in a Cherie Amulet car consists of several stages.

Unscrew the oil filler cap.
Clean the plug covering the crankcase drain hole.
Place a container under the opening and then drain the used oil into it.
Replace the stopper.
Remove the filter.
Coat the ring of the new filter with clean engine oil. But this should be done only if it was not pre-treated with grease or talc during the manufacturing process.
Replace the filter without using tools.
Fill with new engine oil to the correct level.
Tighten the oil filler cap.

Draining the used grease

Be careful because the temperature of the drained fluid is high. Check the gasket installed on the plug. If it is badly damaged, it must be replaced. A special wrench is usually used to unscrew the filter. If you don't have one, a regular screwdriver will work. You can also move it with sandpaper.

After the operations performed, it remains only to start the Cherie Amulet engine and let it run idle for a few minutes. The signal light, which means a drop in pressure in the car's engine, should go out a few seconds after starting the engine. If this does not happen, you should contact the service department for the help of specialists.

While your car's engine mechanism is running, check for oil drips under the drain plug or under the filter. Then stop the engine and check the level again with the dipstick. Add lubricant if necessary. Your Chery Amulet is ready for use!

maslomotors.ru

What kind of oil to pour into the engine Cherie Amulet

Changing engine oil is a fairly simple procedure in servicing a car - even one like the well-known Chery Amulet liftback. The 2005 model year car, copied from the brand model, was a very popular model in the Russian market. The car has earned a good reputation for its simple design and inexpensive parts. The quality of the car, it must be admitted, is appropriate, to match other Chinese cars of that time. Surprisingly, but this model is still in demand, despite the presence of more modern budget cars. In this article, we'll take a look at which oil is best for your Chevrolet Amulet engine. The topic of choosing a suitable motor fluid is now more relevant than ever, given the reluctance of the owners to carry out expensive maintenance in the Chery branded service.

Oil change nuances

It is noteworthy that in the mid-2000s, when this car went on sale, the owners immediately encountered difficulties in changing the oil - the fact is that on the Internet and even in the user's manual for the car, there was no detailed information regarding the characteristics and various markings for engine oil. Over the ten years of conveyor production, the machine received two minor updates, along with which the parameters of the liquid poured into the internal combustion engine were gradually improved. For the entire production period, the car was offered with two motors - a low-power 8-valve, or a relatively modern 16-valve internal combustion engine. The first unit, provided by GM, is considered to be very reliable and is designed to run on fuels with different octane numbers. At the same time, this engine is less demanding on the quality of engine oil. As for the 16-valve valve, little should be selected for it solely on the basis of the optimal parameters.

Oil types

As for other modern cars, Chery Amulet motor oil is divided into three types:

Mineral oil - This lubricant is based on the atmospheric distillation of crude oil. There is also an improved type of mineral lubricant - the so-called hydrocracking oil, which is produced using an identical technology, but at the same time it is still subjected to vacuum distillation for improved cleaning from fuel oil.
Synthetic oil is the most expensive and technically advanced oil used in modern cars... In fact, the Chevrolet Amulet can be attributed to them, albeit with some reservations. Unlike mineral water, a gaseous medium is used for the manufacture of synthetics. Such a product, of course, has excellent performance properties - largely due to the minimum content of harmful impurities.
Semi-synthetics are a kind of golden mean between the above two lubricants. And yet, more than half of such oil consists of mineral oil - from oil and gas synthesis. This is a better quality lubricant than mineral, and at the same time, more affordable compared to pure synthetics.

What kind of oil to fill in Chery Amulet

When changing the oil for the first time, it is recommended to thoroughly flush the Chevrolet Amulet engine. If this is not done, there is a high risk of mixing the new oil with the old one (which was filled earlier, for example, at the factory). Mixing is highly undesirable since both oils may have incompatible properties and parameters. This can lead to undesirable consequences, and the properties of the new oil may lose their activity upon contact with the old oil. In this regard, we can conclude that it is better to fill in the oil that was originally filled from the factory. If such a liquid is not available, then analogs with similar parameters should be used.

Marking

The marking provides important information about the quality of the lubricant, as well as its compatibility with the specific ambient temperatures in which the vehicle is operated. So, let's pay attention to the abbreviation SAE - this is how the international quality certificate is denoted. Other symbols can be found on the label, for example the capital letter W, indicating winter adaptation. By the way, it is better to fill in synthetic oil in winter. It is more fluid and almost never freezes when exposed to low temperatures. Mineral oil is the thickest and freezes faster than other lubricants.

The full marking of the temperature viscosity looks something like this - 5W-40, where 5W indicates the preservation of the properties of the oil at a temperature of - (minus) 25 degrees. The number 40, on the other hand, indicates the highest temperature for such an oil. Please note that this parameter (5W-40) has two values at once - for low and high temperatures. For example, if only the first digit is indicated, then the oil is calculated only for winter temperatures.

Now we will consider the best brands of motor oils, as well as the parameters for them separately for each lineup Chery Amulet:

Model Year 2006

SAE viscosity parameters:

Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40, 25W-40

Model Year 2007

SAE viscosity parameters:

All-weather - 10W-40, 15W-40, 5W-40
Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40
Type - semi-synthetic
The best brands - Mobile, ZIK, Xado, Lukoil, Rosneft, Mannol, G-Energy, Valvoline, Kixx, ZIC

Lineup 2008

SAE viscosity parameters:

All-weather - 5W-40, 10W-40, 15W-40
Winter - 0W-30, 0W-40, 5W-40
Summer - 20W-40, 25W-40
Type - semi-synthetic
The best firms - Mobile, Lukoil, ZIK, Kixx, G-Energy, Xado, G-Energy

Lineup 2009

SAE viscosity parameters:

All-weather - 5W-40, 15W-40
Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40
Type - semi-synthetic
The best firms - Mobile, ZIK, Xado, Lukoil, G-Energy, Kixx, Valvoline

Lineup 2010

SAE class:

All-weather - 10W-40, 15W-40, 5W-40
Winter - 0W-40, 0W-30, 5W-40
Summer - 20W-40, 25W-40
The best firms - Castrol, Mobile, Xado, ZIK, Lukoil, Kixx, Valvoline

Lineup 2011

SAE class:

All-weather - 10W-40, 15W-40, 5W-40
Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40
Type - synthetic, semi-synthetic
The best firms - ZIK, Mobile, Xado, Shell, Castrol, Lukoil, Valvoline, GT-Oil

Lineup 2012

SAE class:

All-weather - 10W-40, 10W-50, 15W-40, 5W-40
Winter - 0W-40, 5W-40, 5W-50
Summer - 20W-40, 25W-40, 25W-50
Type - synthetic, semi-synthetic
The best firms - Castrol, Shell, Mobile, Xado, ZIC, Lukoil, GT-Oil, Valvoline

Lineup 2013

SAE class:

All-weather - 10W-50, 15W-40, 5W-40
Winter - 0W-40, 5W-50
Summer - 20W-40, 25W-50
Type - synthetic
The best firms - Mobile, Castrol, Shell, Xado, Valvoline, ZIK, Lukoil, GT-Oil

Lineup 2014

SAE class:

All-weather - 10W-40, 15W-40
Winter - 0W-40, 0W-50
Summer - 20W-40, 25W-40
Type - synthetic
The best firms are Castrol, Shell, Mobile, ZIK, Xado.

maslospec.ru

When to change the engine oil Cherie Amulet

Features of engines and lubrication systems in Chery Amulet

In the basic configuration, the models use three types of engines (volume - 1.6 liters):

SQR480ED;
SQR480EC;
TRITEC 1.6L.

These are water-cooled, 4-cylinder in-line engines. The first two have 2 valves per cylinder, and the third - 4.

These motors have a built-in combined lubrication system (both under pressure (for camshaft bearings, main and connecting rod bearings) and by splashing). This system includes the following components:

oil pump (gear);
oil receiver;
oil sump;
full-flow filter;
pressure meter.

The movement of the lubricant passes through the lubrication channels.

What kind of oil is used in Cheri Amulet?

Chery Amulet, produced since 2006, is filled with the following types of engine oil:

semi-synthetics;
synthetics.

In previously released models, it is possible to use mineral (or rather, hydrocracking) oil.

When choosing products, they are guided by the viscosity index (SAE) and the oil quality index (API). Moreover, the newer the car, the higher the requirements for motor lubrication. For example, mineral water can be poured into the Chery Amulet 2003 engine, after 2006 - semisynthetics, and in the restyled variation (2-3 generation) - preferably only synthetics.

In addition, it is worth paying attention to which season the oil is designed for: summer, winter or year-round use.

How do you know when to change your oil?

But if you use a car in difficult conditions (dusty air, engine overload, etc.), it is worth replacing the lubricant at least every 5000 km. This will help protect the engine from premature wear.

The level is checked using a special dipstick according to the following procedure.

Stop the engine, open the hood and wait 3-5 minutes (so that all the oil flows into the crankcase).
Check filter and crankcase for leaks while waiting. If there is a leak from the crankcase, you need to fix it: with a rubber patch, "cold welding" or other materials at hand. If the filter is damaged, it must be replaced urgently. Also, leakage in this place may be due to insufficient tightening.
Remove the dipstick from the crankcase, wipe it, insert it into place and remove it again. Normally, the oil level mark should be between the marks on the dipstick.

It is also worth paying attention to the condition of the oil:

structural changes (graininess, lumps);
unnatural smell (for example, burning);
discoloration (darkening, blackening).

How to change or add engine oil in Chery Amulet?

Open the oil filler cap.
Unscrew the drain plug and drain the oil into a container.
Check the condition of the gasket on the drain plug, replace if necessary.
Flush the engine with special flushing oil (or the same one that will be filled in).
Screw on the drain plug.
Remove the oil filter with a special wrench.
Lubricate the O-ring of the new filter with oil.
Put the filter back in place and manually lock it by turning it 3/4 of a turn.
Fill in new grease through the oil filler neck (3.5-4 l).
Close the stopper.

After that, the engine is started at idle speed. In this case, the emergency lamp on the pressure sensor should go out. After 3-5 minutes, check the level again and, if necessary, add more.

kitaec.ua

One of the most common questions motorists ask is what kind of oil to put into the engine. Especially often people who have bought a vehicle from a manufacturer, about which they know little, are interested in this.

Cherie Amulet in all its glory

For example, the owners of Cherie Amulet. To make the right choice, everyone should try to understand the characteristics of motor oils. This will help you figure out which one is best for your vehicle.

The number after the letter W indicates the maximum temperature at which the engine oil will retain its properties. The 10W-40 symbol combination means that this grease can be used in all weather conditions, whatever the season. Winter oil would be labeled SAE 10W.

When choosing oil according to the viscosity parameter, pay attention to the pattern of its labeling depending on the temperature at which it can be used.

At a negative temperature of 30 degrees and below, the lubricant must have a 0W mark.
At temperatures from -20 to -25 degrees - 5W.
-15 to -20 - 10W.
If the air temperature in winter ranges from -10 to -15, then you should choose engine oil with the designation 15W.
-5 to -10 - 20W.
If the average temperature is up to -5, auto chemicals with a 25W icon are used.

The difference between mineral products and synthetic

When switching to synthetics, you need to check the strength of the seals, the absence of leaks and deposits. If found, the seals should be replaced. Deposits can be removed by flushing the oil system. To detect smudges, fill in semi-synthetics and watch the engine. If they did not appear when using this type of auto chemistry, you can safely switch to synthetics.

Changing the lubricant and filter in the engine

Add grease

It is not necessary to drain the working off on the ground, use some kind of container.

The process of changing the oil in a Cherie Amulet car consists of several stages.

Unscrew the oil filler cap.
Clean the plug covering the crankcase drain hole.
Place a container under the opening and then drain the used oil into it.
Replace the stopper.
Remove the filter.
Coat the ring of the new filter with clean engine oil. But this should be done only if it was not pre-treated with grease or talc during the manufacturing process.
Replace the filter without using tools.
Fill with new engine oil to the correct level.
Tighten the oil filler cap.

Draining the used grease

While your car's engine mechanism is running, check for oil drips under the drain plug or under the filter. Then stop the engine and check the level again with the dipstick. Add lubricant if necessary. Your Chery Amulet is ready for use!

Changing engine oil is a fairly simple procedure in servicing a car - even one like the well-known Chery Amulet liftback. The 2005 model year car, copied from the brand model, was a very popular model in the Russian market. The car has earned a good reputation for its simple design and inexpensive parts. The quality of the car, it must be admitted, is appropriate, to match other Chinese cars of that time. Surprisingly, this model is still in demand, despite the presence of more modern budget cars. In this article, we'll take a look at which oil is best for your Chevrolet Amulet engine. The topic of choosing a suitable motor fluid is now more relevant than ever, given the reluctance of the owners to carry out expensive maintenance in the Chery branded service.

Oil change nuances

Oil types

As for other modern cars, Chery Amulet motor oil is divided into three types:

Mineral oil - This lubricant is based on the atmospheric distillation of crude oil. There is also an improved type of mineral lubricant - the so-called hydrocracking oil, which is produced using an identical technology, but at the same time it is still subjected to vacuum distillation for improved cleaning from fuel oil.
Synthetic oil is the most expensive and technically advanced oil used in modern cars. In fact, the Chevrolet Amulet can be attributed to them, albeit with some reservations. Unlike mineral water, a gaseous medium is used for the manufacture of synthetics. Such a product, of course, has excellent performance properties - largely due to the minimum content of harmful impurities.
Semi-synthetics are a kind of golden mean between the above two lubricants. And yet, more than half of such oil consists of mineral oil - from oil and gas synthesis. This is a better quality lubricant than mineral, and at the same time, more affordable compared to pure synthetics.

What kind of oil to fill in Chery Amulet

Marking

Now let's consider the best brands of motor oils, as well as the parameters for them separately for each Chery Amulet model range:

Model Year 2006

SAE viscosity parameters:

Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40, 25W-40

Model Year 2007

SAE viscosity parameters:

All-weather - 10W-40, 15W-40, 5W-40
Winter - 0W-40, 5W-40
Summer - 20W-40, 25W-40
Type - semi-synthetic
The best brands - Mobile, ZIK, Xado, Lukoil, Rosneft, Mannol, G-Energy, Valvoline, Kixx, ZIC